Dive Centre
You have no items in your cart.

Alternate Air Sources


Aqualung Airsource 3 Quick Disconnect Complete

MANUFACTURER: Aqualung
CODE: 15251
PRICE:$449.00

Green Tick Small IN STOCK NOW!

Streamlined for peace of mind, the redesigned and refined Airsource 3 regulator combines a high-performance Pneumatically balanced second stage with a breathable power inflator that lets you ditch your octi off your reg forever!

Features:

 

  • Streamlined: Don't have an octi on your regulator! One less hose means you're more stremlined and your alternate air source is easier to find if needed.
  • Conveniently Positioned: Deliver life-saving air at a moment’s notice: the Airsource sits right in front of you throughout your dive.
  • Pneumatically Balanced: The second stage is pneumatically balanced for consistent breathing throughout your dive. Ideal for use with over-balanced first stages.
  • Lightweight Flexi-Hose: New, lighter-weight flexi-hose is softer, making it easier to pull open the rapid exhaust valve. Includes clips and recessed areas to accommodate your MP hose.
  • Trim Grip: The Trim Grip control in the middle of the flexi-hose lets you dump air from your BCD during ascent without removing the mouthpiece.
  • Soft-touch: Purge Cover Located on the bottom, the soft-touch purge cover prevents accidental activation in strong currents.
  • Travel-Friendly: The Airsource quickly separates from its bayonet mount on the BCD at the Trim Grip so that you can pack it with the complete regulator.

Specs

      

Type of second stage  - 

Pneumatically balanced

Mouthpiece  - 

Comfo-bite

Hose  - 

Braided, flexi, lightweight

Weight  - 

1.3 lbs

Outer body  - 

Over-molded

Trim Grip  - 

detachable

Dust covers  - 

2 included

Nitrox compatible  - 

Yes to 40% O2 when new, out of the box

Care & Maintenance

How to properly care for your Aqua Lung regulator: 

It is important to provide the proper preventative maintenance in order to ensure the best possible performance and maximum life of your Aqua Lung Regulator.

The following maintenance procedures should be performed routinely after each use to ensure that the regulator is cleaned, inspected, and prepared for the next use or for storage. 

As soon as possible after diving, the regulator should be rinsed thoroughly with fresh water while it is attached to a cylinder and pressurized with air. Rinsing alone, however, will not sufficiently clean the regulator.

To clean the regulator as thoroughly as possible Aqua Lung recommends: Attach the regulator to a charged SCUBA cylinder, open the cylinder valve to pressurize the regulator, and thoroughly soak both the first and second-stages in a bath of fresh water.While the regulator is soaking, move the vane adjustment switch on the second stage (if present) back and forth several times from the “MIN” (or “—”) to the “MAX” (or “+”) settings.

You may also turn the valve adjustment knob (adjustable models) slightly back and forth—no more than 1/4 turn. After the regulator has been properly soaked, it is important to rinse it vigorously by flushing the mainspring cavity of the first stage regulator (non- environmentally sealed models only), the second-stage mouthpiece, and the openings in the second-stage front cover with a pressurized stream of water. This will remove the deposits of salt and minerals that were loosened during soaking. 

<<DANGER>> If you use a garden hose, do not use the high pressure jet as this could damage the diaphragm and the internal valve. 

<<WARNING>> DO NOT depress the purge button, loosen the first stage yoke screw, or turn the second stage adjustment knob all the way “out” (adjustable models) if the regulator is submerged unpressurized. Doing so will allow the entrance of moisture, and will require that the regulator be returned to an Authorized Aqua Lung Dealer for service. Disconnect the regulator and wipe it as dry as possible and then hang it by the first stage to ensure that all remaining moisture drains from the second stages.

Do not leave the regulator exposed to direct sunlight for long periods. When the regulator is completely dry, store in a clean equipment box, or sealed inside a plastic bag. Do not store it where it may be exposed to extreme heat or an electric motor, which produces ozone. Prolonged exposure to extreme heat, ozone, chlorine, and ultraviolet rays can cause premature degradation of rubber parts and components. Never store the regulator while it is still connected to the cylinder valve. 

<<DANGER>> Do not use any type of solvent or petroleum based substances to clean or lubricate any part of the regulator. Do not expose any part of the regulator to aerosol spray, as some aerosol propellants attack or degrade rubber and plastic materials.

All details, prices and availability are subject to change - All rights reserved Dive Centre Ltd 1972-2022